体育彩票11选5

不锈钢储酒罐的支撑及正确的使用方式

发布于:2020-11-17 15:28:47  来源:

不锈钢储酒罐一般选择托耳支撑,即在夹套部位上端焊有托耳型的支撑方式,属悬空式支撑,这样与其它设备如冷凝器、管道、储罐等配套使用,选择托耳支撑的要有操作台,操作台的设计是根据反应釜的尺寸,用槽钢、圆管等组合而成,根据工艺的所配套的其它设备也就便于安装操作。
Stainless steel wine storage tank generally adopts lug support, that is, the upper end of the jacket is welded with lug type support, which belongs to suspended support. In this way, it can be used with other equipment such as condenser, pipeline, storage tank, etc. the supporting lug should have an operating platform. The design of the operating platform is based on the size of the reaction kettle, combined with channel steel, circular pipe, etc., according to the process matching other The equipment is easy to install and operate.
如果是单体使用反应釜,一般选择支腿支撑,即在不锈钢储酒罐底部的夹套部位含有三根或四根腿型的支撑,属落地式支撑,尤其是小的不锈钢储酒罐一般容积在500L以下的,选择这种支撑方式不用焊接操作台,放置、移动比较方便,但非常重要的一点就是要确定支腿的长度,换言之即底阀到地面的度,支腿的长度一般是在500mm左右,但要根据您的具体使用情况如怎样接料用什么样的容器接料等来确定您所需要的长度。
If a single reactor is used, the support legs are generally selected, that is, there are three or four leg supports in the jacket part at the bottom of the stainless steel wine storage tank, which belongs to the floor type support. Especially for the small stainless steel wine storage tank with the volume below 500L, it is not necessary to weld the operation platform to select this support mode, which is convenient to place and move. However, it is very important to determine the support The length of the leg, in other words, is the degree from the bottom valve to the ground. The length of the outrigger is generally about 500mm, but the length you need should be determined according to your specific use, such as how to receive the material and what kind of container to receive the material.
不锈钢储酒罐的正确使用方法介绍:
How to use stainless steel wine tank correctly
1) 校正pH电极和溶氧电极。
1) Adjust pH electrode and dissolved oxygen electrode.
不锈钢内胆实木酒桶
2) 不锈钢储酒罐用罐体。根据需要将培养基配入罐体,按要求封装后,小型不锈钢储酒罐(5L)可将罐体放入大**锅**(115℃,30分钟);大型不锈钢储酒罐(10L及以上)采用蒸汽**(121℃,30min)。
2) Stainless steel wine tank body. The culture medium is added into the tank according to the requirements. After being packaged according to the requirements, the small stainless steel wine storage tank (5L) can put the tank body into the large * * pot * * (115 ℃, 30 minutes); the large stainless steel wine storage tank (10L and above) adopts steam * * (121 ℃, 30min).
3) 待不锈钢储酒罐的罐体冷却后,将其置于台上,安装完成;打开冷却水,打开气泵电源,连接通气管道开始通气,调节进气旋钮使通气量适当,使罐压保持在0.05MPa;设置温度、pH、搅拌速度等,并在确定的转速和通气量下对溶氧电极进行斜率标定,数值为100
3) After the tank body of the stainless steel wine storage tank is cooled, put it on the stage and complete the installation; turn on the cooling water, turn on the power supply of the air pump, connect the ventilation pipe to start ventilation, adjust the air intake knob to make the ventilation volume appropriate, and keep the tank pressure at 0.05Mpa; set the temperature, pH, stirring speed, etc., and calibrate the slope of dissolved oxygen electrode under the determined speed and ventilation rate, the value is 100
4) 待温度稳定,各项参数都正确后,将预摇的种子接入,开始,并开始记录各种参数。
4) When the temperature is stable and all parameters are correct, connect the pre shaken seeds, start timing, and start recording various parameters.
5) 完毕后清洗罐体和电极,将pH电极插入有3M氯化钾的三角瓶中待用,溶氧电极的探头用保护套,保存备用。
5) After that, clean the tank and electrode, insert the pH electrode into the triangular flask with 3M potassium chloride for use, and the probe of dissolved oxygen electrode shall be protected with protective sleeve for standby.
本文由不锈钢内胆实木酒桶整理发布,您是不是对这些内容有所了解了呢?更多的内容请点击:我们会有更多精彩内容等你查看。
This article is published by solid wood barrel with stainless steel liner. Do you have any understanding of these contents? For more information, please click: We'll have a lot more to see.

咨询热线:
0537-4556677